How to connect speakers to a TV

Of course, if you are a fan of watching TV, then you need special conditions. Because for some people, this is not only a normal rest from a working condition, but also getting pleasure and new information using modern technologies. Therefore, it is so important to pay special attention to equipping your vacation spot. Thus, most people prefer to install special speakers so that the sound is of the highest quality. However, it is recommended to consider various points before the process. In the same article, we will try to understand this topic in detail and find out intermediate facts, which will also facilitate simplification during work.

Types of inputs and connectors

Modern televisions have connectors for a wide variety of purposes. Here we will analyze the most basic ones.

1. Video. This is considered the most common - HDMI. It is he who allows you to transmit a signal even on a wide variety of digital units. Each device is equipped with such a hole, and in some of them there may even be several. Accordingly, absolutely every user can enjoy high definition images or video.
2. What follows is the ability to connect a computer to the television that RGB provides. As for quality, this is a slightly weaker option, since the entire load goes to the connection with a digital signal.
3. To use a multimedia device, you need SCART. With its help, both audio and video signals and control communications are transmitted. If you touch on the theme of the image image, then it will be noticeably worse than HDMI. In addition, the connection can be correlated with the same mechanism.
4. S-video. It represents the transmission of not only the color signal, but also the brightness. However, in modern times, this connector is less and less common in use.
5. CVBS As statistics show, this is one of the worst options. The opinion is explained by the fact that it is he who uses not one or two analog signals, but three at once. Naturally, the quality will be worse.
6. The last connector of the “video” type is component. Here, the signals are not mixed, that is, the image is clear.
7. Speaking of audio, you need to remember the mini-jack and RCA connectors. The first of them is used to connect small equipment, and the second - for red, white and audio channels.
8. The next category is the so-called “other” connectors. You can find one like for an antenna. In addition, there is a network port, which helps to connect to a local network or the Internet. USB is needed exclusively for the use of various external storage devices.

Which speakers can be connected to the TV

A great option would be to purchase a speaker system. Because it is with her that you will be provided with excellent sound and the absence of extraneous noise. In addition, additional subsystems can be distinguished in it. So, one of which is active. A feature of such a device is the built-in additional amplifier.

The second component is passive. He, respectively, is the opposite of the previous version. Usually, a horn system is also distinguished, which does not need any amplification mechanism at all. In order to enjoy the bass, it is recommended to purchase a subwoofer. It is he who provides low frequencies and is considered as a specialized speaker.

REFERENCE. As for the simplest method for realizing sound, it's a soundbar.

Is it possible to connect computer speakers to a TV

Yes, of course, they can be connected. Only the principle of the process will be the same as with active equipment. This will require special round sockets, the diameter of which is 3.5 millimeters. This is not a problem even for the most inexperienced users. It is enough to understand this topic and location a little - the back panel of the device.

How to connect speakers to a TV

As you know, there are several varieties of the speaker system, namely the methods of connecting the structure. Below we will analyze each of them for a full understanding.

Active acoustics

As already mentioned above, the meaning of the name is revealed in the principle of operability, namely the presence of an amplifier in the process, which needs a separate power supply of 220 V. If we talk about the composition of the structure, then it is worth mentioning about two columns, in one of which the same additional element is built-in. The connection itself is in the following positions:

• Used connector called "tulip". To do this, you will need exclusively white and red plugs from its part. They will need to be inserted into sockets of the corresponding color. They can be located either on the side of the panel or on the back - depending on the model of the structure. This method is the most practical, since it is possible not only on modern technologies, but also on old samples.
• Mini jack. In this case, you may need to purchase an additional adapter.
• Connect all wires directly directly. There is a generation of televisions that have connectors for exposed parts. They are directed, respectively, directly from the columns.

Passive acoustics

The amplifier in this case is built-in directly into the system - a feature of this mechanism.

ATTENTION. To connect the components, it is very important to consider and pay attention to the polarity of all wires.

Thus, the output on the left side should be connected to the left column, and the right one, respectively. But this applies exclusively to the system, which has only two columns. It may be that the availability exceeds the specified number. In this case, you have to purchase a certain unit - an av receiver. It is he who will be able to connect all communications into a linear one and convert all possible signals. If you are the owner of a built-in receiver, then this will greatly simplify the connection, that is, you are very lucky.

How to connect a soundbar to a TV

It is very important to first determine the location. Because it is on this that the further convenience of interaction will depend.

• Next is to deal with the wires. Of course, it’s best if the TV is ready for digital connection. However, in the absence of such an opportunity, you can use the analog. In the case when you have the opportunity of both the first and second methods, then choose according to your preference.
• Then you can verify the presence of an audio signal. This refers to the fact of sending a signal. To do this, it is advisable to go to the TV menu, there, instead of the built-in acoustics, turn on the external. Thus, it connects once and for all. If you still change your mind about viewing channels through the last system, you will have to re-open the settings and do all the manipulations in the opposite order.
• To use a DVD player or other similar digital sources, you will need a coaxial cable.
• To equip the equipment of portable devices, you will need a mini-jack. It can be connected directly independently or with the use of an additional adapter.
• In addition to the presented methods, which are described above, there is one more. The signal through the sauna bar can be transmitted using HDMI. To do this, activate the function through the settings and menu of the TV. Thanks to this method, you will be limited in the availability of necessary wires, and the sound itself will not deteriorate at all. Of course, it’s better to first familiarize yourself with all the instructions that are attached directly to the device.

How to connect a subwoofer to a TV

It also distinguishes between active and passive acoustics. However, first you need to figure out the place where the entire structure will be located. So:

• If you are active, you should know that there is automatic tuning by using the service menu of the television. As in the previous paragraph, you should refer to the parameters of the unit and specify the setting you need. Thanks to manufacturers of modern technology, the whole process is greatly simplified, which has a fairly positive effect on demand among potential buyers.
• Speaking of a passive variety, it is worth remembering a certain sequence of actions. First you need to connect special wires with the receiver or home theater. Then the subwoofer is connected to the first of these devices in a specific way. Namely, this is done so that the unit is parallel with the front speakers.

ATTENTION! How correctly and thoroughly you approach the issue of polarity equipment will directly affect the life of the entire system. Therefore, it is so important to treat this with understanding and accuracy.

In conclusion, I want to note that in all processes there is definitely nothing complicated, you can connect any equipment to the speakers. Even the most inexperienced master can cope with all actions without the intervention of qualified specialists and additional equipment. You just need to know the basic rules that greatly simplify all work with the connection and devote time and attention to the most seemingly minor details.